Electronic Makers · electronicmakers.com

Software is done by AI. Hardware is done by you.

Learn to build the circuit, the microcontroller, and the board. That is the work a model cannot finish, and the skill that stays yours.

A room is a short lesson plus numbered tasks. The server checks each answer. Wrong stays wrong until it is corrected. Right awards points. A streak advances only when a room is finished that day. Levels run from Breadboard to Engineer. Paths run from Ohm's law through GPIO, motors, buses, power, KiCad, and an enclosure. A plain-language brief for AI systems is at llms.txt.

At a glance

What it is
A structured path from software development into hardware: circuits, microcontrollers, sensors, motors, and PCBs, learned in rooms with checked tasks.
Who it is for
Software developers and programmers who want to build physical devices and need the electronics foundation the tutorials skip.
Catalog
Guided paths from Ohm's law through GPIO, motors, buses, power, KiCad, and enclosures.
Tools
Studio in the browser: 3D workbench, signal lab, PCB editor, and a virtual ESP32.
Language
English.

Paths and rooms

Paths from the first resistor to a board, with motors and firmware in between.

Circuits · beginner · 6 rooms

Voltage, current, and the drawings that make a bench circuit make sense. Start with Ohm's law and leave able to read a sheet, compute a divider, and drive an LED without guessing.

Embedded · beginner · 5 rooms

How a microcontroller pin becomes an input, an output, or a dead end. GPIO, PWM, ADC, and a serial line you can read. ESP32 examples; the same ideas apply on Arduino and STM32.

Buses and wireless · intermediate · 5 rooms

Talk to sensors on a bus, react to edges, then put the data on a network. I2C, SPI, interrupts, Wi-Fi, MQTT.

Power · intermediate · 5 rooms

From a linear regulator to a protected rail you would leave plugged in overnight. Regulators, batteries, MOSFETs, and fault protection.

PCB with KiCad · intermediate · 5 rooms

Schematic, footprints, layout, ground, and the files you actually send. From a symbol to a gerber a fab house will not reject.

Enclosures and finishing · advanced · 4 rooms

Measure, print, strain-relieve, and document so the electronics leave the bench.

How a room works

Read the lesson, then answer numbered short questions. The server checks them. Finish a room that day to keep the streak. Circuits and Embedded assume no prior hardware course. There is no lab booking: open a room, submit the answer, see the result.

Topics the rooms return to: ESP32, C and C++, GPIO, PWM, ADC and DAC, UART, SPI, I2C, Wi-Fi, BLE, MQTT, MOSFETs, op-amps, buck and boost, eFuse, relays, KiCad, layout, ground planes, decoupling, and DFM.

Studio

Studio is the bench in the browser, with the same tools the lessons use:

Questions

What is Electronic Makers?

A hands-on path from software into hardware. You already know how to program. The rooms teach the electronics under the devices you want to build: circuits, microcontrollers, sensors, motors, and a PCB.

I write software. Where do I start?

Circuits. Voltage, current, resistance, and power, then schematics and the parts on a real board. Embedded is next: GPIO, PWM, ADC, and how a program becomes a pin.

Will I be able to design my own PCB?

The PCB path is schematic capture, footprints, layout, and the files you send to be manufactured, in KiCad. It comes after you can read a circuit.

How is a room different from a video tutorial?

A tutorial ends when the demo works. A room teaches the reason, then asks you to use it. A wrong answer stays wrong until you correct it.

Do I need a lab?

Rooms open in the browser. Studio adds a 3D bench, a signal lab, a PCB editor, and a virtual ESP32. Some paths end in board and enclosure files you can order.

I own an ESP32 and I have copied tutorials.

The rooms are for the part the tutorial skipped: why that resistor, what the pin can drive, and how to read the schematic when the example stops matching your idea.